Cloner 3D photogrammetric facial scanner: Assessment of accuracy in a controlled clinical study.

OBJECTIVE: To evaluate the accuracy of facial measurements on three-dimensional images obtained using a new photogrammetric scanner. MATERIAL AND METHODS: A total of 11 participants were included in the study. Nine customized adhesive labels were used to identify the facial landmarks: Trichion (Tri), Glabella (G), Right (Exr) and Left (Exl), Pronasal (Pn), Subnasal (Sn), Chelion right (Chr) and left (Chl) and Mentonian (Me). Two trained and calibrated examiners were responsible for performing seven linear measurements for each participant (Tri-G, Sn-Me, Exr-Exl, Chr-Chl, Exr-Chr, Exl-Chl, Pn-Sn) first with a digital caliper and later with a three-dimensional model obtained after digitalization with photogrammetric technology. The intraclass correlation coefficient (ICC), mean difference, SD, and Bland-Altman correlation were used to compare the measurements performed. RESULTS: Intra and inter-examiner reliability were excellent (ICC >0.9). In general, the measurements presented a variation of a minor 2.0 mm. However, only three measures (Sn-Me, Exr-Exl, and Exr-Chr) were outside the clinical acceptability range. CONCLUSIONS: The 3D Cloner scanner showed clinically acceptable accuracy comparable to the digital caliper with a variation of -0.8 ± 1.2 mm. Inter- and intra-examiner agreement on digital measurements was also observed. CLINICAL SIGNIFICANCE: Scanners with accurate 3D model reproductions associated with reliable digital measurements provide a more precise diagnosis and better planning in orofacial treatment.

The influence of hydrogen peroxide concentration on the chemical kinetics of photo-accelerated tooth whitening.

BACKGROUND: The bleaching procedure consists of chemical principles of free radical release that react with chromophores, which results in an amount of energy released in this process. However, the evaluation of the electrical potential generated in these protocols has not yet been thoroughly investigated in the literature. Thus, this study aimed to examine variations in pH, mV, and temperature of different concentrations of hydrogen peroxide in the presence or absence of an intermittent LED/LASER photo acceleration system. METHODS: The study was divided into six groups (n = 9) according to the concentration of hydrogen peroxide (6%, 15%, and 35%), associated or not with the photo acceleration system LED/LASER. We followed the variation of pH, mV, and temperature at 1, 5, 10, 15, and 30 min after gel manipulation. Data were evaluated by two-way ANOVA of repeated measures (α =0.05). RESULTS: pH, mV, and temperature of the groups showed statistical differences both in the light and bleach and in the interaction between the two factors (p < 0.0001), where pH and mV were more influenced by the bleach and light factor, while the temperature was influenced by the bleach factor associated with light. HP15 presented the most significant change in pH, mV, and temperature. CONCLUSION: The use of LED/laser increased the temperature of the gels and altered the pH and mV kinetics of HP6 and HP15, which did not occur in HP35, possibly due to the high ionic potential linked to the concentration.

aPDT associated with sequestrectomy in the treatment of osteonecrosis in cancer patients with metastasis: Case report.

INTRODUCTION AND IMPORTANCE: Bisphosphonates are drugs that have demonstrated effectiveness in the prevention and treatment of bone metastases from malignant neoplasms and other diseases of bone metabolism and although they represent a risk factor for osteonecrosis. PRESENTATION OF CASE: The present case depicts a patient with prostate neoplasia and metastases, referred to the dental department because he presented severe periodontal infection in the previous incisors of the mandible and was under treatment by intravenous zoledronic acid. A panoramic x-ray showed a marked bone loss with a periodontal infection that indicated the tooth exodontia of the affected teeth. However, 2 months after the removal of the dental elements, bone sequestration was detected a CT scan confirmed that. Surgery was then performed to remove mandibular bone sequestration and photodynamic therapy (aPDT) treatment for decontamination of the affected area. DISCUSSION: There was a tissue reconstitution of the site in 3 weeks and total eradication of bone necrosis with aPDT treatment associated with bone sequestration. CONCLUSION: aPDT has proven to be an effective complementary treatment for the process of tissue decontamination and photostimulation in cases of BRONJ.

Assessment of the temporal variation of electrical potential and pH of different bleaching agents.

INTRODUCTION: Tooth whitening procedures are under continuous investigation to improve esthetic outcomes and reduce bleaching sensitivity (BS) precipitating from treatments. During the dental bleaching process it is known that the release of free radicals degrades the organic pigment molecules of the tooth and with this an amount of energy is released. Nonetheless, previous studies have never investigated the temporal correlation between of pH and electric potential (EP) generated in this treatment. OBJECTIVES: Therefore, the objective of the present study was to investigate temporal variations of pH and EP associated with three different commercially available bleaching gels and the correlation levels between parameters of interest to provide relevant information regarding the kinetics of oxidation reactions in dental bleaching procedures. METHODS: The study was divided into 3 groups (n = 9) in function of hydrogen peroxide concentration (either 6%, 15% and 35%). The temporal evolution of pH and EP values were determined using a highly-accurate and previously calibrated pH meter at specific time-points (5, 10, 15 and 30 min). RESULTS: Data obtained were submitted to one-way ANOVA of repeated measures with Bonferroni post-test (α = 0.05). The results of the study showed difference in the factor gel concentration (p < 0,0001), time (p < 0,0001) and interaction (gel/time) (p = 0.002) while throughout the intervals evaluated the groups remained relatively stable and without significant difference in the intragroup variation of pH (p < 0.05) and in EDP only with significant difference in the 5 min interval of the 35% concentration. A 2nd order polynomial relationship test showed high correlation levels. CONCLUSION: It can thus be concluded that there is a negative relationship between EP and pH variation in the different gel concentrations. CLINICAL SIGNIFICANCE: The findings of the present study suggest that bleaching gels of higher concentration may provoke BS that are more intense and durable due to significant electric depolarization of neuronal extensions of pulpal tissues.

Association of microabrasion and tooth whitening with LED/laser system in the treatment of incisor hypomineralization: 3-year follow-up.

The hypomineralization of enamel is characterized as a defect in the quality of the enamel during the maturation process. This presents with clinical consequence as a whitish and rough appearance that effects the aesthetics of the dental elements. In recent years there has been a significant increase in this pathology, which has led to a great demand from professionals in the search for knowledge and appropriate technique to treat cases. Minimally invasive therapy may be sufficient for the aesthetic return of the altered enamel. Thus, the present clinical case aimed to present an aesthetic treatment of enamel hypomineralization in the upper incisors with a minimally invasive approach of association of microabrasion with low concentration tooth whitening photoaccelerated by violet LED and infrared laser. The follow-up of the case was performed for 3 years and the association of the techniques proved effective in returning the aesthetics and well-being of the patient, appearing as a good conservative alternative for the treatment of enamel hypomineralization.

mILIB: a new concept in laser therapy / mILIB: un nuevo concepto en laserterapia

mILIB (Intravascular Laser Irradiation in the Modified Bloodstream) presents itself as one more photobiomodulation technique, among the many therapeutic possibilities we know. The advantage in this case is the possibility of making application in a systemic way in which the organism as a whole is benefited. The use of the red therapeutic laser in a transcutaneous way, has been a great option as an added therapeutic value to the treatment of several pathologies, providing systemic stimuli, similar to hemotherapy. Thus, mILIB presents itself as an effective and increasingly widespread technique for professionals working with photobiomodulation

mILIB (Irradiación láser intravascular en el torrente sanguíneo modificado) se presenta como una técnica de fotobiomodulación más, entre las muchas posibilidades terapéuticas que conocemos. La ventaja en este caso es la posibilidad de realizar una aplicación de forma sistémica en la que se beneficia al organismo en su conjunto.El uso del láser terapéutico rojo de forma transcutánea, ha sido una gran opción como valor terapéutico añadido al tratamiento. de varias patologías, proporcionando estímulos sistémicos, similar a la hemoterapia. Así, mILIB se presenta como una técnica eficaz y cada vez más extendida para los profesionales que trabajan con fotobiomodulación.

Low-level laser therapy (830 nm) on orthodontic pain: blinded randomized clinical trial.

The objective of this research was to compare the effect single low-level laser therapy (LLLT) irradiation on pain perception in patients having fixed appliance treatment in the clinic of orthodontics. Sixty-two patients were recruited to participate in this randomized, double-blinded, placebo-controlled study. The patients were assigned to four groups: group I-laser on the right side; group II-placebo on the right side; group III-laser on the left side; group IV-placebo on the left. The laser or placebo was applied before separation, 24 and 48 h after separation of their first permanent molars in the lower arch. Just after the separation, the average of the pain for the placebo group was 1.6, significantly greater than the average of 1.1 registered for the laser group (p = 0.013). After 24 h and before the new irradiation, the values registered among the different groups did not show any differences. In relation to the gender, only after the first irradiation in placebo group, the female had a level of pain (0.1) significantly higher (p = 0.04) compared to male, and after 48 h, the group where the laser was applied had a difference (p = 0.04) among the gender with a value of lower pain for men (0.6) than for women (1.6).The laser irradiation to minimize the pain was only effective when applied immediately after treatment and separation. In general way, there were no differences between the genders, except after the first placebo group irradiation in which the female had a significantly higher level of pain compared to male and after 48 h. The pain cycle observed in this study had its peak in 24 h, both for laser's and placebo's group.

Confecção digitalizada 3D de placas oclusais / Occlusal splints 3D digitized preparation

Os distúrbios da articulação temporomandibular (DTMs), bruxismo, apertamento dental, problemas oclusais e estresse são as principais causas que motivam o cirurgião-dentista a indicar a utilização terapêutica de placas oclusais. A confecção dessas placas no modo tradicional é amplamente divulgada na literatura mundial, porém devido a diferentes filosofias e técnicas de confecção, bem como falta de comunicação precisa com o protético, diversos dentistas apresentam dificuldade na perfeita indicação e instalação das placas oclusais. Assim o objetivo desse artigo é apresentar de maneira simplificada as etapas de desenvolvimento das placas oclusais com tecnologia digital, desde o escaneamento intrabucal até a impressão 3D e instalação no paciente. As principais vantagens que estimulam cada vez mais o desenvolvimento da técnica digital estão relacionadas à diminuição de possíveis erros de confecção, juntamente com maior precisão nas etapas aliadas ao custo similar dos procedimentos tradicionais, integrando ainda um menor tempo de execução.(AU)

Temporomandibular joint disturbances (TMD), bruxism, dental tightening, occlusal problems and stress are the main causes that lead the dentist to indicate therapeutic occlusal splints. The manufacturing of these splints in the traditional way is widely spread in the worldwide literature, however due to different manufacturing philosophies and techniques, as well as lack of precise communication with the prosthodontist, it is difficult for several dentists the perfect indication and installation of the occlusal splints. So the objective of this article is to present in a simplified way the stages of the occlusal splints development with digital technology, from the intraoral scanning to the 3D printing, and installation in the patient. The main advantages that stimulate more and more the development of the digital technique are related to the reduction of possible manufacturing errors, together with bigger precision in the stages combined to the similar cost of traditional proceedings, also integrating a shorter execution time (AU)

Bioluminescence Analysis of Antibacterial Photodynamic Therapy Using Methylene Blue Mediated by Low-Intensity Level Laser Against Cariogenic Biofilms.

OBJECTIVE: A non-destructive and real-time bioluminescence (BL) assay was used to determine the utility of antimicrobial photodynamic therapy (aPDT) treatments mediated by methylene blue (MB) and laser irradiation (LI) against intact biofilms that are capable of producing caries (cariogenic). The efficacy of antibacterial photodynamic treatments has been currently determined by using either viable colony counts (VCC) or metabolic assays (Alamar Blue) that were demonstrated to have critical limitations when used on microcolony-forming bacteria such as Streptococcus mutans. MATERIALS AND METHODS: Resin composite specimens were fabricated, wet-polished, ultraviolet-sterilized, and stored in water (72 h). S. mutans (strain JM10) biofilms were grown [24 h; 0.65 × THY with 0.1% (w/v) sucrose] on the surfaces of sterile specimens. Antibacterial treatments were performed by using MB (0.0005% and 0.001%) with or without LI (660 ± 10 nm, 6 J/cm2). Specimens treated with chlorhexidine gluconate served as the negative control group. The efficacy of aPDT treatments was determined in terms of BL for intact biofilms and VCC for sonicated bacteria. RESULTS: BL results were corrected by using the Greenhouse-Geisser method and were analyzed with repeated-measures analysis of variance and post hoc Bonferroni test (α = 0.05). VCC results were analyzed by using Kruskal-Wallis and Dunn's multiple-comparisons post hoc tests (α = 0.05). Our findings demonstrated that experimental treatments significantly decreased the viability of S. mutans biofilms (p < 0.05). Moderate reductions in cellular viability were observed on biofilms subjected to aPDT treatments. CONCLUSIONS: This study demonstrated that aPDT has promising potential to be used as an additional method to control oral cariogenic biofilms.

A novel approach for in-office tooth bleaching with 6% H2O2/TiO_N and LED/laser system-a controlled, triple-blinded, randomized clinical trial.

UNLABELLED: The purpose of this randomized, parallel, triple-blinded clinical trial was to compare efficacy and tooth sensitivity (TS) after use of an in-office bleaching agent of 6% hydrogen peroxide containing nanoparticles of nitrogen-doped titanium oxide (HP6) vs. 35% hydrogen peroxide (HP35). Forty-eight volunteers were randomly divided either a HP6 or HP35. Two clinical sessions were performed with an interval of 7 days between them for each group. In each session, two consecutive applications of each bleaching agent were performed and activated by a hybrid LED/laser light. Efficacy was determined by color alteration (ΔE), recorded with reflectance spectroscopy. It was assessed at baseline and after the first and second bleaching session. TS was characterized according to occurrence, intensity, duration, and type. Efficacy was analyzed by repeated measures analysis of variance (ANOVA) and post hoc Bonferroni test, and TS was analyzed by means of chi(2) test (α = 0.05). For HP35, highest and significant values of ΔE were found after bleaching when compared to HP6 (p = 0.002). However, HP35 showed a significantly higher occurrence of TS than HP6 (p = 0.008). Also, intensity and duration were higher in HP35. The majority of volunteers classified the type experienced in their sensitivity in the form of a "shock." The use of HP6 despite reducing efficacy when compared to an in-office bleaching in higher concentration (35%) produced less tooth sensitivity. CLINICAL RELEVANCE: In terms of tooth sensitivity, the use of lower concentrations of in-office bleaching should be the first choice, suggesting greater biocompatibility and safety compared to a conventional HP35.

Low level laser effect after micro-marsupialization technique in treating ranulas and mucoceles: a case series report.

The aim of this preliminary study was to investigate the influence of low level laser therapy (LLLT) in alleviating pain caused by micro-marsupialization and the healing of oral ranulas and selected mucoceles. Eleven patients underwent micro-marsupialization treatment associated with LLLT. The patients were irradiated with a 660-nm continuous wave from an indium-gallium-arsenide-phosphorous (InGaAsP) diode laser, at 100 mW, with a spot size on the tissue surface of 0.0283 cm(2) (irradiance = 3.53 W/cm(2)). Irradiation was carried out immediately following micro-marsupialization treatment, as well as at 24, 48, and 72 h post-micro-marsupialization. All treated oral ranulas and selected mucoceles presented clinical healing. No evidence of recurrence could be identified during a mean of 11.0-month follow-up period. The use of InGaAsP diode lasers, within the parameters tested, appears to present a good alternative treatment to reduce pain and heal oral ranulas and selected mucoceles associated with micro-marsupialization.

Comparação entre soluções irrigadoras na endodontia: clorexidina x hipoclorito de sódio / Comparasion between irrigants solutions in endodontics: chlorhexidine x sodium hypocloride

O objetivo dessa revisão foi relatar uma visão geral e descritiva a respeito das propriedades de duas soluções irrigadoras, a solução de hipoclorito de sódio e de clorexidina com diferentes concentrações, utilizadas no tratamento de canais radiculares. Uma solução irrigadora considerada ideal deve apresentar ação antimicrobiana, dissolver resíduos teciduais, promover molhamento com finalidade de facilitar a instrumentação, e apresentar biocompatibilidade com os tecidos adjacentes. O hipoclorito de sódio utilizado em diferentes concentrações para limpeza de canais radiculares tem sido a solução de escolha entre os profissionais por apresentar ação antimicrobiana e atuar como solvente tecidual. Porém, atualmente, a clorexidina vem sendo muito utilizada como solução irrigadora devido a propriedades específicas que viabilizam sua utilização, tais como substantividade, efetividade antimicrobiana, e baixa toxicidade. Desse modo concluí-se que a solução de clorexidina com diferentes concentrações se apresenta como uma possível alternativa de solução irrigadora para o tratamento de canais radiculares.

The objective of this review was reporting an overview about the properties of two irrigating solutions, solution of sodium hypochlorite and chlorhexidine, used in the treatment of root canals. A solution must submit irrigating antimicrobial action, dissolve waste tissue, promote wetting to facilitate the instrumentation, and present biocompatibility with the adjacent tissues. The sodium hypochlorite used in different concentrations has been the solution of choice among professionals by presenting antimicrobial action and act as a solvent tissue. However, today, chlorhexidine has been widely used as an irrigating solution due to specific properties that enable its use, such as substantivity, antimicrobial effectiveness, and low toxicity. Thus the solution of chlorhexidine with different concentrations is presented as an alternative to irrigating solution for the treatment of root canals.

Regional odontodysplasia in early childhood: a clinical and histological study.

Regional odontodysplasia (RO) is a rare disorder of dental development. The affected teeth are clinically hypoplastic and hypocalcified, presenting a ghost-like appearance radiographically. The aim of this work was to report a clinical case of a child with both primary and permanent dentition affected by RO. The conducted therapy was based on a conservative approach, which consisted of follow-up clinical evaluations of the anomalous teeth. However, the endodontic treatment of the primary incisors failed. Then, the chosen option for patient rehabilitation became extraction followed by removable of prosthesis confection. The extracted teeth were processed for histological analysis. In spite of the uncertain prognosis, but taking into account the psychological aspects of the patient, a conservative approach in an attempt to maintain those viable teeth in the oral cavity should be established.

Ricinus communis biocompatibility histological study in the nose of Cebus apella monkeys.

UNLABELLED: Bone tissue lesions can be caused by congenital and acquired factors, and result in nasal deformities with cosmetic and functional repercussion. Surgical treatment in these cases frequently requires complex reconstructions and the use of biomaterials. The polyurethane derived from castor beans (Ricinus communis) has a favorable formulation in terms of ease of processing, flexibility, no emission of toxic vapors and low cost. Nonetheless, despite favorable results, studies about the use of castor beam polymer (Ricinus communis) assessing tissue reaction on the nasal dorsum are still missing in the literature. AIM: the goal of the present investigation is to histologically assess the Ricinus communis polymer implant biocompatibility with the nasal dorsum. STUDY DESIGN: experimental. MATERIALS AND METHODS: we used four Cebus appela monkeys, in which we created a nasal dorsal defect in all the animals and there we placed the aforementioned implant. The animals were sacrificed 270 days after surgery and the samples were submitted to histological study. RESULTS: in the histology analysis we did not observe the presence of foreign body granulomas or phagocytic cells. We also observed a progressive bone formation and maturation. CONCLUSION: macroscopic and microscopic results showed that the castor oil polymer implant was biocompatible.

Ricinus communis biocompatibility histological study in the nose of Cebus apella monkeys / Avaliação histológica da biocompatibilidade do polímero da mamona no dorso nasal de macacos-pregos (Cebus apella)

Bone tissue lesions can be caused by congenital and acquired factors, and result in nasal deformities with cosmetic and functional repercussion. Surgical treatment in these cases frequently requires complex reconstructions and the use of biomaterials. The polyurethane derived from castor beans (Ricinus communis) has a favorable formulation in terms of ease of processing, flexibility, no emission of toxic vapors and low cost. Nonetheless, despite favorable results, studies about the use of castor beam polymer (Ricinus communis) assessing tissue reaction on the nasal dorsum are still missing in the literature. AIM: the goal of the present investigation is to histologically assess the Ricinus communis polymer implant biocompatibility with the nasal dorsum. STUDY DESING: experimental. MATERIALS AND METHODS: we used four Cebus appela monkeys, in which we created a nasal dorsal defect in all the animals and there we placed the aforementioned implant. The animals were sacrificed 270 days after surgery and the samples were submitted to histological study. RESULTS: in the histology analysis we did not observe the presence of foreign body granulomas or phagocytic cells. We also observed a progressive bone formation and maturation. CONCLUSION: macroscopic and microscopic results showed that the castor oil polymer implant was biocompatible.

Lesões do tecido ósseo podem ser causadas por fatores congênitos e adquiridos e resultar em deformidade nasal com repercussão estética e funcional. O tratamento cirúrgico desses casos requer reconstruções complexas e frequentemente o uso de biomateriais. O poliuretano derivado do óleo da mamona apresenta uma fórmula com aspectos favoráveis de processabilidade, flexibilidade de formulação, ausência de emissão de vapores tóxicos e baixo custo. Entretanto, a despeito dos resultados favoráveis, estudos referentes ao uso do polímero de mamona, avaliando a reação tecidual no dorso nasal, ainda não foram realizados. OBJETIVO: O objetivo deste estudo consiste em avaliar histologicamente a biocompatibilidade do implante do polímero de mamona no dorso nasal. FORMA DE ESTUDO: Experimental. MATERIAL E MÉTODO: Foram utilizados quatro macacos-pregos da espécie Cebus apella. Um defeito ósseo foi realizado no osso nasal em todos os animais e colocado um implante de polímero de mamona. A eutanásia foi realizada com 270 dias de pós-operatório, e as amostras foram submetidas a estudo histológico. RESULTADOS: Na análise histológica não foi observada a presença de granuloma de corpo estranho ou células fagocitárias. Progressiva formação óssea e maturação foram observadas. CONCLUSÃO: Os resultados macroscópicos e microscópicos mostraram que o implante de polímero de mamona foi biocompatível.

Reparação tecidual pulpar sob ação bioestimuladora do laser de baixa intensidade (LILT), e do diodo emissor de luz (LED): Estudo em macacos prego / Pulp tissue repair under the biostimulation action of Low-level laser therapy (LLLT) and of light-emitting diode (LED): Study in Capuchin monkeys

O estudo investigou os efeitos da radiação eletromagnética não ionizanteemitidos pelos diodos LASER com comprimento de onda no espectro 688 ηm e 785 ηm, e diodo LED 635 ± 10 ηm, associados ao capeamento direto comhidróxido de cálcio em exposições pulpares mecânicas. Avaliou-se assim em dentes de macacos-prego a resposta pulpar baseado na morfologia das célulaspulpares, no processo inflamatório local, na formação da barreira mineralizada, ena organização do tecido pulpar nos diferentes grupos estudados. Discutiu-setambém as diferentes fontes de emissão de radiação eletromagnética comparandoos resultados obtidos de estimulação pulpar com os diodos LASER e LED, osquais apresentam energia coerente e não-coerente, respectivamente. Os resultado mostraram uma estimulação em todos os grupos irradiados com melhores resultados para o estímulo com LASER, quando comparado ao grupo tratado isoladamente com hidróxido de cálcio. Concluímos assim que a estimulação de energia eletromagnética LASER e LED associado ao capeamento pulpar direto com hidróxido de cálcio apresentou aceleração no processo de reparação tecidual. Porém, há necessidade de novos estudos com diferentes parâmetros de irradiaçãoa fim de se obter protocolos cada vez mais eficientes para o estudo dos efeitos da luz sobre o processo de reparação pulpar.

Reparação tecidual pulpar sob ação bioestimuladora do laser de baixa intensidade (LILT), e do diodo emissor de luz (LED): estudo em macacos prego / Pulp tissue repair under the biostimulation action of low-level laser therapy (LLLT) and of light-emitting diode (LED): study in capuchin monkeys

O estudo investigou os efeitos da radiação eletromagnética não ionizante emitidos pelos diodos LASER com comprimento de onda no espectro 688 ηm e 785 ηm, e diodo LED 635 ± 10 ηm, associados ao capeamento direto com hidróxido de cálcio em exposições pulpares mecânicas. Avaliou-se assim em dentes de macacos-prego a resposta pulpar baseado na morfologia das células pulpares, no processo inflamatório local, na formação da barreira mineralizada, e na organização do tecido pulpar nos diferentes grupos estudados. Discutiu-se também as diferentes fontes de emissão de radiação eletromagnética comparando os resultados obtidos de estimulação pulpar com os diodos LASER e LED, os quais apresentam energia coerente e não-coerente, respectivamente. Os resultado mostraram uma estimulação em todos os grupos irradiados com melhores resultados para o estímulo com LASER, quando comparado ao grupo tratado isoladamente com hidróxido de cálcio. Concluímos assim que a estimulação de energia eletromagnética LASER e LED associado ao capeamento pulpar direto com hidróxido de cálcio apresentou aceleração no processo de reparação tecidual. Porém, há necessidade de novos estudos com diferentes parâmetros de irradiação a fim de se obter protocolos cada vez mais eficientes para o estudo dos efeitos da luz sobre o processo de reparação pulpar.

The aim of this study was to compare the effects of non-ionizing electromagnetic radiation emitted by LASER diodes 688 ηm and 785 ηm, and LED diode 635 ± 10 ηm associated to direct pulp capping with calcium hydroxide in traumatic pulp exposures were investigated. Based on pulp cells morphology, on the local inflammatory process, on mineralized barrier formation and on pulp tissue organization, the pulp response in capuchin monkey teeth was evaluated in different groups. It was also discussed the different electromagnetic radiation emission sources effects comparing the obtained results of pulp stimulation with diodes LASER and LED, which present coherent and non-coherent energy respectively. Stimulation was observed in all irradiated groups, being the best results achieved with LASER stimulation, when compared to the group treated only with calcium hydroxide. Thus, it is concluded that the electromagnetic LASER and LED energy stimulation associated with calcium hydroxide direct pulp capping accelerated the tissue repair process. However, further studies with different stimulation parameters in order to obtain increasingly efficient protocols to study light effects on pulp repair are necessary.

Effect of low-level laser therapy on bone repair: histological study in rats.

BACKGROUND AND OBJECTIVES: Bone remodeling is characterized as a cyclic and lengthy process. It is currently accepted that not only this dynamics is triggered by a biological process, but also biochemical, electrical, and mechanical stimuli are key factors for the maintenance of bone tissue. The hypothesis that low-level laser therapy (LLLT) may favor bone repair has been suggested. The purpose of this study was to evaluate the bone repair in defects created in rat lower jaws after stimulation with infrared LLLT directly on the injured tissue. STUDY DESIGN/MATERIALS AND METHODS: Bone defects were prepared on the mandibles of 30 Holtzman rats allocated in two groups (n = 15), which were divided in three evaluation period (15, 45, and 60 days), with five animals each. control group-no treatment of the defect; laser group-single laser irradiation with a GaAlAs semiconductor diode laser device (lambda = 780 nm; P = 35 mW; t = 40 s; Theta = 1.0 mm; D = 178 J/cm(2); E = 1.4 J) directly on the defect area. The rats were sacrificed at the pre-established periods and the mandibles were removed and processed for staining with hematoxylin and eosin, Masson's Trichrome and picrosirius techniques. RESULTS: The histological results showed bone formation in both groups. However, the laser group exhibited an advanced tissue response compared to the control group, abbreviating the initial inflammatory reaction and promoting rapid new bone matrix formation at 15 and 45 days (P<0.05). On the other hand, there were no significant differences between the groups at 60 days. CONCLUSION: The use of infrared LLLT directly to the injured tissue showed a biostimulating effect on bone remodeling by stimulating the modulation of the initial inflammatory response and anticipating the resolution to normal conditions at the earlier periods. However, there were no differences between the groups at 60 days.